Jump to content

Refinishing copper wedge

Recommended Posts

I posted this in another forum but realized this is more appropriate:

I am putting an old TaylorMade Hi Toe wedge with a copper finish back in the bag and as you can see from the photos below the copper finish is coming off.  Its not a big deal and just cosmetic, but does anyone have any suggestions how how to either touch it up or completely remove it for a raw finish?





  • Driver-  Ping G410 Plus 9*
  • Fairway- Tour Edge Exotics EXS 220 3 Wood 16.5*
  • Hybrid- Tour Edge Hot Launch C521 19* & 22* 
  • Irons-PXG 0211 DC, 5-PW
  • Wedges-  Taylormade Hi Toe 50*, 54* and 58*
  • Putter- Ping Sigma G Tyne (Superstroke grip)
  • Ball- Snell MTB-X Maxfli Tour X
  • Bag- 2021 Ping Hoofer USA Edition 
  • Arccos 
Link to comment
Share on other sites

  • 2 weeks later...

It wont bring back the copper but it will clean it up. 

Some 000 steel wool or and aggressive greenie with alot of elbow grease will clean it up. 

They do make that for a drill attachment. You ca then hold the club in a vice and be a bit more precise and WAAAAY faster. 


  • Like 1

Driver - 44.5" 5.0 flex 10.5 deg ACCRA tour Z GP MCC4+ 1 deg closed

Irons - 5-pw, GW stnd length 5.0 flex same grip 1 deg flat. Type low medium offset cavity back, no diggers

Wedges - 56 and 60 tour grind wedge spinner and mcc4+ grip 2 flat 10 and 8 in bounce

Putter - 33" 3 deg loft 70 lie, lrg slight line slightly toe hang

Ball - truvis

Carried in a Sun Mountain C-130 USA bag - BE PROUD.

HC - LH but 85 is a good number, playing in Ohio.

Link to comment
Share on other sites

You can use a product know as Scotch-Brite. These are abrasive pads also called carbide hair. They are in a pad form. I will cut some up into circles and the put a hole through the middle. Then take a bolt nut and washers to make your own grinding wheel type arrangement. Put this in a drill and go to town. Once done then go to a finer grit to polish. I do this on clubs all the time.   

  • Like 2

:titleist-small: Driver, TSi1 10* Stiff Flex

:taylormade-small: 3 Wood, SLDR  HL 17*  R Flex

:taylormade-small: 5 Wood, SLDR 19* R Flex

:cobra-small: 7 Wood, F6 22.5* R Flex

:Sub70: 939x 5 hybrid

:Sub70: Irons, 699 Pro's S Flex (6 - AW)

:Sub70:  JB Wedge 56*

:cleveland-small: Wedge, CBX 60*

:odyssey-small: Putter, Marksman Fang 35"

Link to comment
Share on other sites

I'm not an expert on refinishing by any means, but if you decide to use an abrasive to remove the copper be sure to wear some kind of respiratory protection because you don't want to be breathing in all of that copper dust

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Create New...