Jump to content

DIY golf shaft puller/pusher only £15 to make all in


maccer1001
 Share

Recommended Posts

  • 1 month later...

I love our golfer diy ingenuity on this forum!  Nicely done!  How many shafts have you pulled with it?

Instagram:  @tony_rosselli_

:SuperSpeed:Training

Pre training max driver speed: 124mph

Current: 130mph

WITB:

Driver: :ping-small:G400 LST 8.5* with HZRDUS SMOKE 6.5 70g 

Woods: :taylormade-small: 2007 Burner TP 3 wood and 5 wood

Irons:  :srixon-small: Z765 4-PW (1 degree flat) with KBS $-130 shafts

Wedges:  :vokey-small: SM7 50/12/F, 54/10/S and 58/12/D

Putter: 681811256_Odysseylogo.png.499799aea6663befa411c8db1d859702.png Stroke Lab Ten S 33"

Ball:  :titelist-small: ProV1

Link to comment
Share on other sites

  • 2 weeks later...
  • 4 weeks later...

Interesting. Thanks for sharing. 

Nige
"A bad attitude is worse than a bad swing"
Driver:    Ping i25 9.5 dialled down to 9.0 
Wood:     Slazenger 3 wood
Hybrid:   Ping i25  17*
Irons:      Ping i25 4-SW stiff shaft Green dot (factory adjusted - I only live an hour away)
Wedge:   Cougar Tour Touch I 50*    
Wedge:   Cleveland RTX 588 58*
Putter:   Wilson Staff Infinite THE "L" 
Balls:      Srixon Distance (based on personal testing - work best for my game)
Other:    Shot Scope - can't live without the data! 

Link to comment
Share on other sites

  • 1 month later...

I just pulled an entire set of iron shafts using this method.  I wanted to say thank you so much for sharing.  Saved me $100s and let me save my graphite shafts time toss on eBay. 
 

i ended up melting the ferrule first and sliding it down under the brake spreader to use as a “padding” so I didn’t scratch the shafts as it was being pulled.  Not sure if that makes sense but it helped. 

Link to comment
Share on other sites

On 2/10/2022 at 3:43 AM, maccer1001 said:

I made a cheap DIY golf shaft puller/Pusher for £15 all in. The only equipment needed besides the ones described below are a bench mounted vice and a hand grinder with steel slotting disc plus some sharp HSS drills to 9mm.

Buy a disc pad spreader - I used the Neilson one off ebay £10
A golf shaft rubber vice clamp (£3 off ebay)

You will need some sharp HSS drills up to 9mm and a steel slotting disc on a hand grinder to make the slots for the shaft, the spreader steel is hardened so sharp drills needed. Ensure all edges of slots are deburred to avoid scratching your precious shafts
See pic below of completed mods to spreader
See pic below of device in place ready to push shaft off

You don't need a lot of heat to soften the epoxy holding the shaft in. Works 100% and will last a lifetime

20220208_122727.jpg

20220208_122743.jpg

20220208_122757.jpg

20220208_123158.jpg

Nice job, how wide does the caliper open? Or did you change the bolt for a longer one, I bought the crow bar which is fine for steel shafts but problematic with Graphite. 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

×
×
  • Create New...